Connect audio source components to amplifiers and receivers with this AudioQuest Yukon XLR analogue-audio cable, meticulously designed for exceptional performance and outstanding value. Solid Perfect-Surface Copper+ (PSC+) conductors minimize distortion, Polyethylene Air-Tube insulation preserves dynamic contrasts, and a Carbon Mesh-Network Noise-Dissipation efficiently dissipates high-frequency noise. The result is cleaner, clearer, more naturally beautiful music.

Key Features & Technology Explained

Solid Perfect-Surface Copper+ (PSC+) Conductors
Solid conductors prevent electrical and magnetic strand-interaction. PSC+ Solid-Copper minimizes distortion caused by grain boundaries and maximizes linear RF Noise-Dissipation.

Carbon-Based 3-Layer Noise-Dissipation
It's easy to accomplish 100% shield coverage. Preventing captured Radio Frequency Interference (RFI) from modulating the equipment's ground reference requires AQ's Noise-Dissipation System (NDS). Traditional shield systems typically absorb and then drain noise/RF energy to component ground, modulating and distorting the critical "reference" ground plane, which in turn causes a distortion of the signal. NDS's alternating layers of metal and carbon-loaded synthetics "shield the shield," absorbing and reflecting most of this noise/RF energy before it reaches the layer attached to ground.

Direction-Controlled Conductors
All drawn metal strands or conductors have a non-symmetrical, and therefore directional, grain structure. AudioQuest controls the resulting RF impedance variation so that noise is drained away from where it will cause distortion. The correct direction is determined by listening to every batch of metal conductors used in every AudioQuest audio cable. When applicable, arrows are clearly marked on the connectors to ensure superior sound quality. For most models of AQ cable, the arrows not only indicate the direction that optimizes metal-directionality as part of Noise-Dissipation, but also indicates non-symmetrical attachment of shield and GND in order to optimize full-system performance. A fundamental aspect of AudioQuest's multifaceted Noise-Dissipation technology, Direction-Controlled Conductors ensure induced noise is dissipated and drained properly.

Polyethylene Air-Tube Insulation
Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy. Some of this energy is stored and then released as distortion. AudioQuest, however, uses Polyethylene Air-Tube Insulation on both conductors, for increased geometry stabilization and improved clarity. Because air absorbs next to no energy and Polyethylene is low-loss and has a benign distortion profile, Polyethylene Air-Tube Insulation, with its high air content, causes much less of the out-of-focus effect common to other materials.

Triple-Balanced Geometry
Our Triple-Balanced Geometry uses a separate ground-reference conductor, so the cable's shield is never used as an inferior conductor. Whether prepared with RCA or XLR plugs, the cable's three conductors ensure that the positive and negative signals have equally superior, low-distortion conducting paths.

Cold-Welded, Hanging-Silver Directly Over Pure Purple Copper Terminations

• Solid Perfect Surface Copper+ Conductors: Solid conductors prevent electrical and magnetic strand-interaction. Solid PSC+ Copper minimizes distortion caused by grain boundaries and maximizes linear RF Noise-Dissipation. The result is clearer, cleaner, more naturally beautiful sound.
• Carbon Mesh-Network: AudioQuest’s Noise-Dissipation technology significantly reduces the RF Noise that reaches active circuits and causes masking effects.
• Polyethylene Air Tube Insulation: Because air absorbs next to no energy and Polyethylene has a benign distortion profile, Polyethylene Air-Tube Insulation, with its high air content, causes much less of the out-of-focus effect common to other materials. The result is clearer, more coherent sound.
• Triple Balanced Geometry: AudioQuest’s Triple-Balanced Geometry uses a separate ground-reference conductor, so the cable’s shield is never used as an inferior conductor. The cable’s three conductors ensure that the positive and negative signals have equally superior, low-distortion conducting paths.
• Cold-Welded Hanging-Silver over Pure Purple Copper Terminations: Cold-welding bonds the plug to the wire using high pressure, preserving the character of the wire at the point of termination. Hanging-Silver directly over high-purity Purple Copper further ensures uncompromised signal transfer.